How To Find A Hole In An Air Mattress? 7 Surprising Ways To Find A-Hole!

How To Find A Hole In An Air Mattress 7 Surprising Ways To Find A-Hole!

Are you searching for the best way to find the leak in an air mattress? Stop searching and start reading this article without further ado. Finding a hole in an air mattress by completely submerging a mattress in water is among the most effective ways to locate a difficult-to-find leak, but it is one of the most time-consuming ways.

First, examine the mattress labeling to ensure that submerging this in water would not harm the material and joints. Completely inflating the mattress would make submerging hard. Whereas the hole might occasionally be vast and obvious, very often, it’s not a speck that is invisible to the human eye.

There seem to be various techniques to figure out where the hole in an air mattress comes originates. As you further delve into this article, you will find the easy ways to find a hole in an air mattress. So let’s get started reading further and discover what you want.

Is It Normal For An Air Mattress To Lose Air?

The answer is yes Because air mattresses start losing air, and they will probably never deflate quickly. Locating an airbed that is not depleted throughout a few days or weeks is difficult, despite being a prevalent issue. When you search the internet for data on how lengthy an air mattress could remain filled, you would be astonished to learn that you may use an air mattress for an extended period without ever losing pressure.

What Are The Reasons For Losing Air In An Air Mattress?

Almost every air mattress can lose air because of many reasons. Whenever people lie on such an air mattress, all air within the bed is compressed by the body weight. So the higher the stress upon that air which pulls it out, the greater you weigh. As a result, bulkier persons are more likely to experience air loss in their mattresses.

Check More: How to Fix a Hole in an Air Mattress?

What Are The reasons Of Losing Air In An Air Mattress

Temperature changes are yet another typical cause of air mattresses deflating. When you leave a mattress outside during the cold and don’t take it indoors before bedtime, this will harden and collapse due to the absence of heat. Heat also causes the mattress to leak by reducing the air level.

Even when they’re not used, air mattresses start losing air over time. Airflow within the bed swells as the mattress matures when this is fresh. As a result, if you are using an air mattress once and then never inflate it again, this will collapse in weeks or even months.

How Does Deflating Cause In An Air Mattress?

Deflating is caused by a pressure difference between two ends of an air mattress. If stopping the aging process is complicated, maintaining an air mattress filled with usage may help. Every air mattress deflates. Because all air beds employ the same substance, which does not have a flawless form, therefore generally lose air. As a consequence, they will eventually lose multiple perspectives.

Even though every brand deflates the same way, each brand uses various methodologies to remedy the issue and preserve them for more than just a few weeks. There are several tricks to keeping an airbed filled for as long as possible: Get an air pump to inflate the mattress and achieve the desired pressure fully. Always use your air mattress on a leveled surface.

When using an air mattress on an irregular surface, the bed will leak less air than it has to. As a consequence, you must inflate or deflate the mattress while standing. Avoid placing the air mattresses after it has been filled because they will lose pressure. Moreover, even the tiniest motion during the night can cause you to alter posture and force out air.

Read More: How to Keep an Air Mattress from Deflating

Tips To Store Air Mattress

If you keep an inflated or unwrapped mattress in a cupboard or even other confined places, the mattress may lose its pressure owing to an oxygen deprivation flow. Deflated air beds must be folded up during the night and disconnected from the inflated fabric early morning. Instead, air would build in the mattress’s inner portion. Its mattress loses air as a consequence of this.

Tips To Store Air Mattress

Adhesive and silicone tape could be used to block off the borders of the inflated air mattress against the motion, which will reduce air decline. One can seal the air mattress using rollers or duct tape, so it never leaks or loses air.

7 Ways To Find A Hole In An Air Mattress

Finding a hole in the air mattress is becoming difficult sometimes; following the right ways to locate the hole can save you time, so read the below-mentioned steps carefully to find the hole in your air mattress.

1. Examine the air mattress valves

Inspect the connections before checking for a possible leak inside the air mattress. This will reduce the wastage of effort. Ensure each valve stopper is fully inserted into the control valve. Many valves have two locking positions. Whenever the valve is put within the mattress, it secures, and once the valve cover is placed into the stem, it provides a further level of safety. Ensure the stem was inserted into the mattress.

Furthermore, look all around the stem for any fractures at the bottom that can create leakage. Users won’t be able to restore the valve if it is broken. Continue if indeed the valve plug has been fitted into the stem and the stem has been placed into the mattress.

2. Visually check your air mattress

While it might seem simple, visually examining the air mattress is among the most effective techniques to detect leakage. When you start the assessment, make sure the bed is properly inflated. Increasing force on the material causes even tiny pores to widen whenever the mattress is filled, rendering them more visible. To spot any holes, conduct the check-in in a well-lit area to make it simpler.

Check This: How to Inflate Air Mattress With Electric Pump

Visually check your air mattress

Use a flashlight if needed to increase visibility. During the investigation, be diligent. To prevent losing any parts, begin with one corner of a mattress, then work your way through portions. Check for releasing air with the fingers. Holes frequently originate at joints, so inspect each thoroughly. Once you’ve found the leak, make an important note on it with a spot of permanent ink.

3. Mattress submerging

Fully submerged a mattress in water is among the most effective methods for locating a leak, but it is one of the most time-consuming. First, examine the mattress labeling to ensure that submerging this in water would not harm the material and joints. Completely inflating the mattress would make submerging hard.

If you have access to a big waterbody, including a pool, completely submerge your mattress, and check for air bubbles that signal air leaving. Use a bathtub if there isn’t a pool nearby. Submerge the valve under water and squeeze the mattress to push air out of it.

4. Make Soapy Water

Pour the pail halfway with water so that the towel is thoroughly submerged. So when water gets sloshed or swirled, a considerable amount of dish soap must create enormous soapy bubbles. This is the most helpful way to find out the holes.

Ensure the inflatable air mattress is in an open space with plenty of room. Begin by inflating it to its maximum capacity, but don’t go overboard. It is simpler to locate a leak with more air pressure behind this one. On the other hand, over-inflation can lead to a broader hole, broken seams, and stress tears at vulnerable places. Make sure the workspace is free of gadgets and other water-polluting things. (For example, smartphones, and beds.)

Read It: How to Fix an Air Mattress Bubble

Make Soapy Water

Wet the sponge thoroughly before beginning at one of your air mattress’s ends. Rub a sponge over the entire surface in a single direction, making sure to moisten the seams. To drive air towards the place you’re operating on, move gently, then add pressure. Keep an eye out for bubbles, which signal you’ve discovered the hole and are bleeding air.

Apply this method to all surfaces, including the head, bottom, joints, or corners. Mark the leak’s location with tape or even a marker so that it would be easy to locate and repair later. Before fixing, make sure the area around the leak is arid.

5. Garden hose can be used

Put your mattress outside on a patio, sidewalk, patio, or a level surface. Saturate your mattress in small areas with a garden hose and sprayer, starting with a valve. After hosing down a place, look for any bubbling within the water before it flows off the air mattress. The bubbles indicate that air flows from the bed, indicating a leak.

Whereas these ways may aid in detecting a leak, one may prevent the aggravation of a leaky mattress by simply adopting precautions to protect it. Don’t overinflate your air mattress. It will increase the probability of a tear by increasing the pressure on the joints. While putting up an air mattress, look around for sharp things. Utilize bedding. Cutting tools, including pet claws, are protected by layers of linens, comforters, or bed pads.

6. Listen to the hissing sound from the air mattress

You may feel air escaping from such a hole inside the air mattress in a quiet area with no distractions. Put your ears near a mattress layer once you’ve inflated it and listen for the noise of air movement. As you get near the hole, the leaking noises would become higher. You will notice a hissing sound and a surge of air in the ear after you have stopped the air mattress leakage.

Listen to the hissing sound from the air mattress

7. Use your hand to find the hole

Feeling such a hole in the air mattresses seems to be another simple examination method. The first stage is to push little air out of the mattress by applying downturn. Next, by one hand, begin at one edge and move laterally across it to locate the air mattress leakage. Soak one hand in icy water and make a blast of air extra noticeable.

This is an effortless method to locate the hole, but it needs a proper feeling sense. When your hand goes on the spot, you notice air touching your hand, and you will quickly figure out the hole.

Check This Guide: How to Stay Warm on an Air Mattress

How To Find A Hole In An Air Mattress – FAQs

How do you find a hole in an air mattress with tissue paper?
A tissue technique is a non-messy way of determining a hole’s origin. Cover areas of an air mattress with tissue paper. Next, push air outside by physically applying weight to the mattress. A rapid updraft would force the tissue paper upwards if it is on the hole. You should be in a location with minimal to no air circulation for this strategy to operate.
Can an air mattress losing air but no hole?
This one is true whether you’re asleep and seated, and two hefty persons sitting in a Twin bed may surpass the company’s weight restriction. This might result in a gradual air leak. Along with the preceding two faults, that is a likely cause for an air mattress leaking air but not having a hole.
How do I stop my air mattress from deflating?
Supervise the temperature of the room, do not overfill the weight limit ability of the mattress, pay more attention to any signs of air loss, never over boost your air mattress, enable the mattress substance to stretch out, keep your mattress away from pets and children, and always store it correctly.


Final Thoughts!

Finally, you have learned the ways and different techniques to locate the hole in an air mattress. Finding the hole in the mattress is hard; it needs proper attention or technique to complete the process.

One should never panic if they find air in the mattress because it is normal and can happen anytime. Always take care of your air mattress to avoid holes. We appreciate you, friends, for reading this article till the end.

Leave a Reply